Can I Set Up A Bathtub Myself?
Can I Set Up A Bathtub Myself?
Blog Article
We have encountered this post about Installing A Bathtub directly below on the net and figured it made good sense to write about it with you on this page.
Installing a bath tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a brand-new one is likewise a moderately hard job. If the old tub is conveniently easily accessible, the project can relocate quickly; if you need to open a wall surface to eliminate the old tub as well as place the brand-new bathtub, the job is a lot harder. In either situation, the project is within a residence handyman's skills, although you will require an assistant to leave the old tub and also embeded in the brand-new one. Ensure you have actually qualified on your own for the job and also fit attempting it. As opposed to employing a professional to take control of a halfway-completed job, it is better to take into consideration utilizing one before you start. Chances are you might need a specialist plumber to make tube connections.
This write-up will help you mount a new bathtub in your shower room if you have actually already acquired a new bathtub and also don't require to change the plan of your previous water supply pipes.
Your devices and material list should make up the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be fairly problematic because of the limited gain access to that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a fabric ready for the staying water that will certainly come from the pipes. Once the supply pipelines have actually been gotten rid of, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from transforming throughout this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing substance.
Prior to moving on to fit the brand-new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the current supply pipes.
If you need to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin guaranteeing that the washers are in location in between the faucet as well as the sink. Safeguard the faucet in position with the supplier given backnut. As soon as the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap connectors. The previous kind needs to be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Making use of both wood boards under its feet, put the tub in the needed position. The wood boards are practical in uniformly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
The next goal is to make certain that the tub is leveled all round. This can be accomplished by checking the level as well as changing the feet on the tub up until the spirit level reviews level.
To install faucets, fit the bottom of the furthest adaptable faucet connector to the ideal supply pipeline by making a compression join; after that do the exact same for the other faucet.
Turn on the water supply and also check all joints and also brand-new pipework for leaks and also tighten them if required. Fill the bathtub as well as likewise inspect the overflow outlet and also the typical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the producer's instruction manual. Tiling and also sealing around the bathtub needs to wait up until the bathtub has actually been utilized at the very least once as this will resolve it into its last setting.
Preparing for the Setup
Firstly, the sustaining framework supplied with the bathroom should be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps device to prevent pressure on the bathtub.
Fit the adaptable tap ports to the bottom of the two faucets making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use all of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its final position.
Tiling Around the Tub
In the location where the bath satisfies the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to split an inflexible seal, causing the water to penetrate the wall in between the bathroom and the tiling, resulting in issues with wetness and also possible leaks to the ceiling below.
You can select from a selection of coloured sealers to assimilate your fixtures and fittings. They are offered in tubes and also cartridges, and also can sealing gaps up to a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of drenched paper or soft rope. Remember to always fill the bathtub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can fracture rather very early if you do not take into account this activity before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the market. It is advisable to fit the tiles using waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed reading our post about A Step-by-Step Guide to Installing a Bathtub. Thanks a ton for taking time to read our posting. Are you aware of another individual who is occupied with How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Take a moment to share it. I appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Need Help? Hire Us Now!
Report this page